top
Water Based Enamel for Kitchen and Bathroom Tiles TITAN
IN MANY COLORS
WHERE TO FIND IT

Water Based Enamel for Kitchen and Bathroom Tiles TITAN

Code 120660108
  • .2 in 1, no primer is needed
  • Suitable for a wide variety of surfaces
  • Glossy and Satin
  • Easy-to-apply
  • Water-based enamel

Delivery at your place

Order phone number 210 008 5999

Multi surface, easy-to-apply, water-based enamel. 2 in 1, no primer is needed and it is suitable for a wide variety of surfaces. To obtain high quality and soft touch finishes. Very hard and resistant to abrasion, scratches, soap and stains of liquor, juice, oil, etc. Very wash resistant. It contains anti mould preservative. Unsuitable for immersion or areas with continuous condensation.

Fields of Application
Enamel to be directly applied on ceramic tiles. Highly suitable for also painting walls, doors, kitchen and bathroom furniture, radiators, PVC and copper tubes, etc. Do not use either on floor tiles or worktops.

Drying at 23ºC: 60 - 90 min.
Recoat time at 23ºC: After 4 hours
Methods of Application: Brush and roller
Equipment Cleaning: Water
Pack sizes: 750 ml

Directions for use
GENERAL REMARKS:
Thoroughly stir the contents in the pack. The surfaces to be painted have to be clean, dry and suitably primed. Remove any rest of dirt, grease, poorly adhered rust and old coatings by using household bleach, thinned 9:1, thinner or stripper, depending on needs.

BARE SURFACES:
Tiles: Deeply clean the surface with diluted household bleach. Rests of grease or silicone may prevent the adhesion of the enamel. For ensuring better adhesion, rub joints with a brush in order to remove any dirt, mould, grease, etc. Remove the silicone joints before painting and reseal them once the enamel is applied. Wait at least 5 days to use the water zones. After 5 days, the surface can be washed with soft detergent. Do not use abrasive products, scourers or brushes as they could scratch the enamel film.

Ceramic porous, rigid PVC, copper, melamine: directly apply 1 or 2 coats of Water Based Enamel for Bathroom and Kitchen Tiles in very humid environments, the sanding of the surface with sandpaper P280 greatly improves the adhesion.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
Wash, softly sand and directly apply 1 or 2 coats of Water Based Enamel for Bathroom and Kitchen Tiles.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
Thoroughly remove all previous coats and proceed as for bare surfaces.

Precautions
Always read the pack label before use. For more information, please refer to the Safety Data Sheet.
Protect the packs from temperatures below 0ºC

  • DESCRIPTION

    Multi surface, easy-to-apply, water-based enamel. 2 in 1, no primer is needed and it is suitable for a wide variety of surfaces. To obtain high quality and soft touch finishes. Very hard and resistant to abrasion, scratches, soap and stains of liquor, juice, oil, etc. Very wash resistant. It contains anti mould preservative. Unsuitable for immersion or areas with continuous condensation.

    Fields of Application
    Enamel to be directly applied on ceramic tiles. Highly suitable for also painting walls, doors, kitchen and bathroom furniture, radiators, PVC and copper tubes, etc. Do not use either on floor tiles or worktops.

  • TECHNICAL INFO

    Drying at 23ºC: 60 - 90 min.
    Recoat time at 23ºC: After 4 hours
    Methods of Application: Brush and roller
    Equipment Cleaning: Water
    Pack sizes: 750 ml

  • NSTRUCTIONS FOR USE

    Directions for use
    GENERAL REMARKS:
    Thoroughly stir the contents in the pack. The surfaces to be painted have to be clean, dry and suitably primed. Remove any rest of dirt, grease, poorly adhered rust and old coatings by using household bleach, thinned 9:1, thinner or stripper, depending on needs.

    BARE SURFACES:
    Tiles: Deeply clean the surface with diluted household bleach. Rests of grease or silicone may prevent the adhesion of the enamel. For ensuring better adhesion, rub joints with a brush in order to remove any dirt, mould, grease, etc. Remove the silicone joints before painting and reseal them once the enamel is applied. Wait at least 5 days to use the water zones. After 5 days, the surface can be washed with soft detergent. Do not use abrasive products, scourers or brushes as they could scratch the enamel film.

    Ceramic porous, rigid PVC, copper, melamine: directly apply 1 or 2 coats of Water Based Enamel for Bathroom and Kitchen Tiles in very humid environments, the sanding of the surface with sandpaper P280 greatly improves the adhesion.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
    Wash, softly sand and directly apply 1 or 2 coats of Water Based Enamel for Bathroom and Kitchen Tiles.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
    Thoroughly remove all previous coats and proceed as for bare surfaces.

    Precautions
    Always read the pack label before use. For more information, please refer to the Safety Data Sheet.
    Protect the packs from temperatures below 0ºC

  • HOW TO'S

  • COLOR LIST

Related products

CONTACT US

ASK us something...

Fill out the form below with your contact information, type your question and press "send". We will respond as soon as possible.