top

Titanlux Varnish Crystal Finish Aspecto Cristal TITAN

Code 12107
  • Very hard and elastic
  • Resistance to weathering, wearing, washes and chemicals
  • Non yellowing

Delivery at your place

Order phone number 210 948 0035

Two-component varnish. Based on Acrylic Polyol with high cross-linking grade and aliphatic isocyanate. Very hard and elastic. Excellent gloss retention and resistance to weathering, wearing, washes and chemicals (grease, petrol, gas-oil, etc. ). Non yellowing. 

Fields of Application
Indoors and outdoors. Ideal for protection of surfaces made of noble and exotic wood (pine, teck...), cork, in high wearing conditions or where an excellent appearance must be kept (bar counters, wood floors, worktops, balconies, chairs, doors. It can also be used on glass-fibre, stone and porous tiles.
 

Product Type: Acrylic polyol and aliphatic isocyanate
Finish: Gloss
Colour (UNE 48073): Clear
Coverage: 11 - 15 m2/l
Drying at 23ºC 60 % RH (UNE 48301): 5 - 7 hours
Recoat time at 23ºC 60% HR (UNE 48283): 18 - 24 hours
Mixing Rate: Base: 4 parts. Hardener: 1 part
Fields of Application: Brush, roller and spray-gun
Equipment Cleaning: TITAN YATE Thinne

 

 

Thoroughly stir the contents in the can. The surfaces have to be clean, dry and suitably prepared. The wood moisture content must not exceed 12% in hard wood and 15% in soft wood. Tropical or resinous wood (such as pine, melis or teak): Thoroughly wash with TITAN YATE Thinner to remove resin.

Apply a first coat on a small surface and check. If there is still resin exudation, please refer to the Technical Service. Otherwise, finish with 2-3 coats of TITANLUX Crystal Finish Varnish.

BARE SURFACES:

Sand the wood following the wood grain. Clean the surface, remove resin or resin secretion and smooth up sharp edges.

Indoor wood: In most cases, 2 coats will be enough.

Outdoor wood: Finish with 3 coats of TITANLUX Crystal Finish Varnish. The overcoating interval between coats have to be 12-24 hours. Sand to matt between every two coats.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:Wash, lightly sand and directly apply.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:Remove unsound or resinous previous varnish coats and proceed as for unvarnished wood.

  • DESCRIPTION

    Two-component varnish. Based on Acrylic Polyol with high cross-linking grade and aliphatic isocyanate. Very hard and elastic. Excellent gloss retention and resistance to weathering, wearing, washes and chemicals (grease, petrol, gas-oil, etc. ). Non yellowing. 

    Fields of Application
    Indoors and outdoors. Ideal for protection of surfaces made of noble and exotic wood (pine, teck...), cork, in high wearing conditions or where an excellent appearance must be kept (bar counters, wood floors, worktops, balconies, chairs, doors. It can also be used on glass-fibre, stone and porous tiles.
     

  • TECHNICAL INFO

    Product Type: Acrylic polyol and aliphatic isocyanate
    Finish: Gloss
    Colour (UNE 48073): Clear
    Coverage: 11 - 15 m2/l
    Drying at 23ºC 60 % RH (UNE 48301): 5 - 7 hours
    Recoat time at 23ºC 60% HR (UNE 48283): 18 - 24 hours
    Mixing Rate: Base: 4 parts. Hardener: 1 part
    Fields of Application: Brush, roller and spray-gun
    Equipment Cleaning: TITAN YATE Thinne

     

     

  • NSTRUCTIONS FOR USE

    Thoroughly stir the contents in the can. The surfaces have to be clean, dry and suitably prepared. The wood moisture content must not exceed 12% in hard wood and 15% in soft wood. Tropical or resinous wood (such as pine, melis or teak): Thoroughly wash with TITAN YATE Thinner to remove resin.

    Apply a first coat on a small surface and check. If there is still resin exudation, please refer to the Technical Service. Otherwise, finish with 2-3 coats of TITANLUX Crystal Finish Varnish.

    BARE SURFACES:

    Sand the wood following the wood grain. Clean the surface, remove resin or resin secretion and smooth up sharp edges.

    Indoor wood: In most cases, 2 coats will be enough.

    Outdoor wood: Finish with 3 coats of TITANLUX Crystal Finish Varnish. The overcoating interval between coats have to be 12-24 hours. Sand to matt between every two coats.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:Wash, lightly sand and directly apply.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:Remove unsound or resinous previous varnish coats and proceed as for unvarnished wood.

  • HOW TO'S

  • COLOR LIST

Related products

CONTACT US

ASK us something...

Fill out the form below with your contact information, type your question and press "send". We will respond as soon as possible.