top

Titanlux Water-based Varnish for Wooden Floors

Code 12136
  • Easy-to-use polyurethane varnish
  • Odour free
  • Glass-like finish
  • Very quick drying
  • Long protection to wooden floors which are exposed to heavy use
  • Highly resistant to marring, impacts, household cleaning products, water, alcohol and grease

Delivery at your place

Order phone number 210 948 0035

Water based varnish for wooden floors, with polyurethane, which creates a crystal-like effect. It is easy to apply, odorless and quick drying. Offers a reliable glossy finish with anti-slip properties.Suitable for wooden floors with frequent use, as it creates a protective film resistant to scratches, domicile detergents, water and stains. It provides long lasting effect to floors made of wood or cork, as well as stairs.

Special for giving a long protection to wooden or cork floors as well as to wooden stairways which are exposed to heavy use.

Product Type: Polyurethane
Finish: Gloss
Colour (UNE 48073): Clear
Density (UNE EN ISO 2811): 1.04 - 1.06 Kg/l
Coverage: 10 - 16 m2/l
Drying at 23ºC 60 % RH (UNE 48301); 30 - 60 minutes
Recoat time at 23ºC 60% HR (UNE 48283): 2 - 3 hours
Fields of Application: Brush and roller
Thinning: 5 % max. It is recommended not to thin.
Thinner: Water
Equipment Cleaning: Water

Thoroughly stir the contents in the pack. The surfaces have to be smooth (sanded), degreased, clean and dry. Just applied, the varnish shows a milky appearance which disappears in a few minutes.

Tropical or resinous wood: Please refer to the Technical Service.

If the varnish is applied at relative humidity below 15% or if the air circulation is poor, the finish could be less glossy.

BARE SURFACES:
Thoroughly roughen the surface with sand tools grain 30 - 40. Smooth up the surface with sand tools grain 60 and 80. Dust off. Apply 2 - 3 coats. Sand between every two coats with fine sandpaper (240 - 280). Apply the last coat varnish coat following the wood grain.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
Sand and dust off. Apply 1 or 2 coats, depending on the surface condition. If they old varnish coats are in poor condition or waxed, remove them  completely and proceed as for bare surfaces.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
Thoroughlly remove old coats and proceded as for  bare surfaces.

  • DESCRIPTION

    Water based varnish for wooden floors, with polyurethane, which creates a crystal-like effect. It is easy to apply, odorless and quick drying. Offers a reliable glossy finish with anti-slip properties.Suitable for wooden floors with frequent use, as it creates a protective film resistant to scratches, domicile detergents, water and stains. It provides long lasting effect to floors made of wood or cork, as well as stairs.

    Special for giving a long protection to wooden or cork floors as well as to wooden stairways which are exposed to heavy use.

  • TECHNICAL INFO

    Product Type: Polyurethane
    Finish: Gloss
    Colour (UNE 48073): Clear
    Density (UNE EN ISO 2811): 1.04 - 1.06 Kg/l
    Coverage: 10 - 16 m2/l
    Drying at 23ºC 60 % RH (UNE 48301); 30 - 60 minutes
    Recoat time at 23ºC 60% HR (UNE 48283): 2 - 3 hours
    Fields of Application: Brush and roller
    Thinning: 5 % max. It is recommended not to thin.
    Thinner: Water
    Equipment Cleaning: Water

  • NSTRUCTIONS FOR USE

    Thoroughly stir the contents in the pack. The surfaces have to be smooth (sanded), degreased, clean and dry. Just applied, the varnish shows a milky appearance which disappears in a few minutes.

    Tropical or resinous wood: Please refer to the Technical Service.

    If the varnish is applied at relative humidity below 15% or if the air circulation is poor, the finish could be less glossy.

    BARE SURFACES:
    Thoroughly roughen the surface with sand tools grain 30 - 40. Smooth up the surface with sand tools grain 60 and 80. Dust off. Apply 2 - 3 coats. Sand between every two coats with fine sandpaper (240 - 280). Apply the last coat varnish coat following the wood grain.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
    Sand and dust off. Apply 1 or 2 coats, depending on the surface condition. If they old varnish coats are in poor condition or waxed, remove them  completely and proceed as for bare surfaces.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
    Thoroughlly remove old coats and proceded as for  bare surfaces.

  • HOW TO'S

  • COLOR LIST

Related products

CONTACT US

ASK us something...

Fill out the form below with your contact information, type your question and press "send". We will respond as soon as possible.