top
Water Based Epoxy Paint 836 TITAN
IN MANY COLORS
WHERE TO FIND IT

Water Based Epoxy Paint 836 TITAN

Code 14063
  • Good chemical and mechanical resistance
  • Scratch resistant
  • Permeable to water vapour.

Delivery at your place

Order phone number 210 948 0035

Water-based epoxy paint for walls and ceiling. Suitable for indoor sanitary installations, slaughterhouses, kitchen deposits, fridges and locals where food is manipulated (indirect contact). For surfaces such as  concrete, plaster, etc. It has good chemical and mechanical resistance. Scratch resistant. Permeable to water vapour. It can be applied even on moistened surfaces (concrete humidity <5.5%).

DRYING: 6 - 12 hours

APPLICATION METHODS: Brush and roller

PRESENTATION: 4L & 10L

FINISH: Semi Gloss

GENERAL REMARKS:
Stir the contents in the pack with a mechanical shaker. The surfaces to be painted have to be dry, sound as well as free from pollutants such as oils, grease, whitewash, efflorescence, etc. Apply only when the floor temperature is at least 3ºC higher than dew point.

BARE SURFACES:
Concrete: It has to be thoroughly set before painting (wait 28 days). The surface has to be dry or lightly wet (concrete humidity must not exceed 5,5%).
Remove efflorescence or whitewash by water jet, or preferably by blasting or sanding. If the surface is too smooth, roughen it by means of blasting or sanding. Remove dust by vacuum cleaning. Thin the first coat (10 - 15%). Let to dry for 12 hours and apply a second unthinned coat. Ensure a suitable air ventilation while application and drying.

Plaster: Thin the first coat (10-15%) and apply a second unthinned coat (or not exceeding a 5% thinning rate). Let to dry 12 hours between every two coats.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
Remove grease, oils and dirt (freshwater jet, cleaning solvent, etc) Before applying the epoxy paint, patch the bare areas until reaching the thickness of the previous coats. Let to dry at least 4 hours (at 23ºC) and apply two coats of this paint. The overcoating interval between both coats has to be of approx. 12 hours.
 

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
If the previous paint system is poorly adhered and/or shows rust, it has to be removed by scraping and/or by deeply brushing and proceed as for bare surfaces.
 

  • DESCRIPTION

    Water-based epoxy paint for walls and ceiling. Suitable for indoor sanitary installations, slaughterhouses, kitchen deposits, fridges and locals where food is manipulated (indirect contact). For surfaces such as  concrete, plaster, etc. It has good chemical and mechanical resistance. Scratch resistant. Permeable to water vapour. It can be applied even on moistened surfaces (concrete humidity <5.5%).

  • TECHNICAL INFO

    DRYING: 6 - 12 hours

    APPLICATION METHODS: Brush and roller

    PRESENTATION: 4L & 10L

    FINISH: Semi Gloss

  • NSTRUCTIONS FOR USE

    GENERAL REMARKS:
    Stir the contents in the pack with a mechanical shaker. The surfaces to be painted have to be dry, sound as well as free from pollutants such as oils, grease, whitewash, efflorescence, etc. Apply only when the floor temperature is at least 3ºC higher than dew point.

    BARE SURFACES:
    Concrete: It has to be thoroughly set before painting (wait 28 days). The surface has to be dry or lightly wet (concrete humidity must not exceed 5,5%).
    Remove efflorescence or whitewash by water jet, or preferably by blasting or sanding. If the surface is too smooth, roughen it by means of blasting or sanding. Remove dust by vacuum cleaning. Thin the first coat (10 - 15%). Let to dry for 12 hours and apply a second unthinned coat. Ensure a suitable air ventilation while application and drying.

    Plaster: Thin the first coat (10-15%) and apply a second unthinned coat (or not exceeding a 5% thinning rate). Let to dry 12 hours between every two coats.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
    Remove grease, oils and dirt (freshwater jet, cleaning solvent, etc) Before applying the epoxy paint, patch the bare areas until reaching the thickness of the previous coats. Let to dry at least 4 hours (at 23ºC) and apply two coats of this paint. The overcoating interval between both coats has to be of approx. 12 hours.
     

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
    If the previous paint system is poorly adhered and/or shows rust, it has to be removed by scraping and/or by deeply brushing and proceed as for bare surfaces.
     

  • HOW TO'S

  • COLOR LIST

Related products

CONTACT US

ASK us something...

Fill out the form below with your contact information, type your question and press "send". We will respond as soon as possible.