top

Marine Varnish Gloss TITAN YATE

Code 297
  • High resistance in marine and freshwater environments

Delivery at your place

Order phone number 210 948 0035

Easy-to-apply alkyd varnish with UV filters. High resistance in marine and freshwater environments. It dries by oxidation. Tough and elastic. Wear-resistant. High gloss retention.

Fields of Application
For the varnishing of wood on pleasure and fishing boats and other structures in coastal areas or very humid environments.

DRYING:6 - 7 h
APPLICATION METHODS: Air Spray-gun, Roller, Brush
Finish:Gloss

Thoroughly stir the contents in the can.The surfaces have to be clean, dry and suitably prepared. Apply by thin coats and softly sand between every two coats.
The wood moisture content must not exceed 12% in hard wood and 15% in soft wood.

BARE SURFACES:
Sand the wood following the wood grain. Clean the surface,remove resin or resin secretion and smooth too sharp edges. To improve protection of wood outdoors, apply one coat of TITANXYL Total Protection 3 or TITANXYL Lasur Undercoat. Finish with 2 - 3 coats of TITAN YATE Marine Varnish.

Tropical and resinous wood: The special features of this kind of wood make drying of varnishes difficult. Wash the surface with TITAN YATE Thinner to remove resin. Apply one first coat on a small surface and watch. If the resin exudation persists, please refer to the Technical Service. Otherwise, finish with 2 - 3 coats of TITAN YATE Marine Varnish.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
When old varnish coats are catalyzable or polyurethane-based, it is necessary tothoroughly sand the surface for removing them. If the old varnish coat is poorly adhered or cracked only on small areas, proceed as follows: Remove the damaged or decoloured varnish by scrapping. Prime with TITANXYL Protection 3 or TITANXYL Lasur Undercoat the bare areas in order to guarantee protection. Carefully cover joints and cracks.Improved results are obtained by sanding to matt old varnish coats. Apply a thin coat of TITAN YATE Marine Varnish on the whole surface. Let to dry. Finish as for bare wood. If the surface has been previously treated with linseed oil, remove it with thinner, scrapper,sanding, etc. After that, proceed as for new wood. If more than two months have elapsed from the application of the last varnish coat, sand to matt before varnishing again

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
Remove unsound or resinous previous varnish coats and proceed as for unvarnished wood.

  • DESCRIPTION

    Easy-to-apply alkyd varnish with UV filters. High resistance in marine and freshwater environments. It dries by oxidation. Tough and elastic. Wear-resistant. High gloss retention.

    Fields of Application
    For the varnishing of wood on pleasure and fishing boats and other structures in coastal areas or very humid environments.

  • TECHNICAL INFO

    DRYING:6 - 7 h
    APPLICATION METHODS: Air Spray-gun, Roller, Brush
    Finish:Gloss

  • NSTRUCTIONS FOR USE

    Thoroughly stir the contents in the can.The surfaces have to be clean, dry and suitably prepared. Apply by thin coats and softly sand between every two coats.
    The wood moisture content must not exceed 12% in hard wood and 15% in soft wood.

    BARE SURFACES:
    Sand the wood following the wood grain. Clean the surface,remove resin or resin secretion and smooth too sharp edges. To improve protection of wood outdoors, apply one coat of TITANXYL Total Protection 3 or TITANXYL Lasur Undercoat. Finish with 2 - 3 coats of TITAN YATE Marine Varnish.

    Tropical and resinous wood: The special features of this kind of wood make drying of varnishes difficult. Wash the surface with TITAN YATE Thinner to remove resin. Apply one first coat on a small surface and watch. If the resin exudation persists, please refer to the Technical Service. Otherwise, finish with 2 - 3 coats of TITAN YATE Marine Varnish.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
    When old varnish coats are catalyzable or polyurethane-based, it is necessary tothoroughly sand the surface for removing them. If the old varnish coat is poorly adhered or cracked only on small areas, proceed as follows: Remove the damaged or decoloured varnish by scrapping. Prime with TITANXYL Protection 3 or TITANXYL Lasur Undercoat the bare areas in order to guarantee protection. Carefully cover joints and cracks.Improved results are obtained by sanding to matt old varnish coats. Apply a thin coat of TITAN YATE Marine Varnish on the whole surface. Let to dry. Finish as for bare wood. If the surface has been previously treated with linseed oil, remove it with thinner, scrapper,sanding, etc. After that, proceed as for new wood. If more than two months have elapsed from the application of the last varnish coat, sand to matt before varnishing again

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
    Remove unsound or resinous previous varnish coats and proceed as for unvarnished wood.

  • HOW TO'S

  • COLOR LIST

Related products

CONTACT US

ASK us something...

Fill out the form below with your contact information, type your question and press "send". We will respond as soon as possible.