top

Titanlak Efecto Madera Wood effect paint TITAN

Code 12390
  • Colour, graining and look of natural wood
  • Easy to apply
  • High covering
  • Smooth, hard, tough and silky finish

Delivery at your place

Order phone number 210 008 5999

Polyurethane special effect lacquer. Based on high solids technology. Easy to apply. High covering. Smooth, hard, tough and silky finish. Colour, graining and look of natural wood. Wash resistant. Intermixable weathering-resistant colours.

Fields of Application
For indoor and outdoor use. Special for imitating wood with a single coat. On any non-porous or enamelled surface: doors, frames, cupboards, household appliances, panelling, windows, etc..
 

DRYING:6 - 8 hours
APPLICATION METHODS: Flat brush (width: 7-8 cm)
PRESENTATION:750 ml and 375 ml.
FINISH:Satin

GENERAL REMARKS:
Stir well before using.
The surfaces to be painted have to be clean, dry and suitably primed.
Remove all existing rests of dirt, grease, poorly adhered rust and previous coatings by using thinner or paint stripper, depending on requirements.
If possible, remove the objects that may interfere with the path of the brush: such as locks, handles, peepholes and sundry
embellishers. Apply in plentiful even coats. Finish with long strokes in the direction of the grain. Straightaway and up to ten minutes after application, highlight the grains, depending on requirements by gently passing the tip of the dripped brush in continuous, parallel or wavy lines in the same direction. You will get more marked grains with uneven tip brushes. Do joints by areas and parallel to the grains.

BARE SURFACES:
Wood: Sand wood following the wood grain, thoroughly clean, remove all resins or resin secretion on the surface and smooth up sharp edges. Apply TITAN Protector, Sealing-Primer or Multi-Purpose Primer depending on requirements.

Iron: TITANLUX Synthetic Rust-Preventive Primer or TITAN Multi-Purpose Primer. For outdoor surfaces, at least two coats of the selected primer will be needed. For indoor surfaces, one coat will be enough.

Melamine stratified resin board: Degrease and sand to matt.

Indoor surfaces: One single coat of TITANLAK Wood Effect is enough on most surfaces.

Outdoor surfaces: For achieving a better resistance to weathering, apply at least two coats of TITANLAK Wood Effect.

MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
Wash, lightly sand and directly apply TITANLAK Wood Effect.
MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
Completely remove all previous paint coats and proceed as for bare surfaces.

  • DESCRIPTION

    Polyurethane special effect lacquer. Based on high solids technology. Easy to apply. High covering. Smooth, hard, tough and silky finish. Colour, graining and look of natural wood. Wash resistant. Intermixable weathering-resistant colours.

    Fields of Application
    For indoor and outdoor use. Special for imitating wood with a single coat. On any non-porous or enamelled surface: doors, frames, cupboards, household appliances, panelling, windows, etc..
     

  • TECHNICAL INFO

    DRYING:6 - 8 hours
    APPLICATION METHODS: Flat brush (width: 7-8 cm)
    PRESENTATION:750 ml and 375 ml.
    FINISH:Satin

  • NSTRUCTIONS FOR USE

    GENERAL REMARKS:
    Stir well before using.
    The surfaces to be painted have to be clean, dry and suitably primed.
    Remove all existing rests of dirt, grease, poorly adhered rust and previous coatings by using thinner or paint stripper, depending on requirements.
    If possible, remove the objects that may interfere with the path of the brush: such as locks, handles, peepholes and sundry
    embellishers. Apply in plentiful even coats. Finish with long strokes in the direction of the grain. Straightaway and up to ten minutes after application, highlight the grains, depending on requirements by gently passing the tip of the dripped brush in continuous, parallel or wavy lines in the same direction. You will get more marked grains with uneven tip brushes. Do joints by areas and parallel to the grains.

    BARE SURFACES:
    Wood: Sand wood following the wood grain, thoroughly clean, remove all resins or resin secretion on the surface and smooth up sharp edges. Apply TITAN Protector, Sealing-Primer or Multi-Purpose Primer depending on requirements.

    Iron: TITANLUX Synthetic Rust-Preventive Primer or TITAN Multi-Purpose Primer. For outdoor surfaces, at least two coats of the selected primer will be needed. For indoor surfaces, one coat will be enough.

    Melamine stratified resin board: Degrease and sand to matt.

    Indoor surfaces: One single coat of TITANLAK Wood Effect is enough on most surfaces.

    Outdoor surfaces: For achieving a better resistance to weathering, apply at least two coats of TITANLAK Wood Effect.

    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN GOOD CONDITION:
    Wash, lightly sand and directly apply TITANLAK Wood Effect.
    MAINTENANCE OF PREVIOUSLY COATED SURFACES IN POOR CONDITION:
    Completely remove all previous paint coats and proceed as for bare surfaces.

  • HOW TO'S

  • COLOR LIST

Titanlak Efecto Madera Wood effect paint TITAN

D.I.Y. VIDEOS

Related products

CONTACT US

ASK us something...

Fill out the form below with your contact information, type your question and press "send". We will respond as soon as possible.